☎ 631-793-9820Get a Quote
Home / Services / Milling & Paving
Appell National · Milling & Paving

Commercial Milling & Paving

When a lot is past patching, Appell National manages the whole resurfacing: milling, base repair, paving, compaction and the restripe, from bid to final walk.

Every parking lot eventually reaches the point where repairs cost more than they save. Milling removes the worn surface down to a sound layer, and a new asphalt mat goes down on top, giving the site a new lot without the cost of a full rebuild.

Appell National Accounts manages milling and paving projects for multi-site customers through our vetted paving partners, with one Appell project manager, one schedule and one invoice. We coordinate the work around your hours, document every phase and finish with fresh striping so the site reopens ready.

What's included

MillingRemove the worn surface to a uniform depth and haul away the millings.
Base & drainage repairFix soft spots and failed base before paving.
PavingNew hot-mix asphalt laid to grade by paving crews.
CompactionSteel-drum rolling for a smooth, dense, long-lasting mat.
Phased schedulingSections paved in phases, nights or weekends, to keep the site open.
Striping & closeoutFresh layout, ADA stalls and a final walk with photo documentation.
Milling & Paving

Milling and overlay vs. full reconstruction

Milling and overlay grinds off the worn top layer of asphalt, usually an inch and a half to a few inches, and replaces it with a new surface. It works when the base underneath is still solid, and it keeps curbs, drains and entrances at the right height.

Full-depth reconstruction removes the asphalt and repairs or replaces the base underneath. It's needed when the base has failed, shown by widespread alligator cracking, deep ruts or chronic drainage problems. Many projects combine the two: an overlay across most of the lot with full-depth repairs in the worst areas.

Signs your lot needs resurfacing

  • Widespread cracking. Cracks and alligator cracking across large parts of the lot, not just in a few spots.
  • Crumbling surface. Loose stone and raveling everywhere, not just at the edges.
  • Repeated repairs. The same areas get patched year after year.
  • Drainage problems. Water pools across wide areas after rain.
  • Age. The lot is approaching the end of its life and maintenance no longer keeps up.

How Appell National runs a paving project

You get one Appell project manager from the first site visit to the final walk. We scope the work from aerial imagery and a site walk, submit one clear proposal, and build a phasing plan that keeps entrances, drive-thrus and customers moving.

Our vetted paving partners mill, repair the base, pave and roll. When the new surface is ready, we restripe the lot with a fresh layout and accessible stalls, and close out with before-and-after photos, including in your facilities portal if you use one.

Protecting the new investment

New asphalt lasts longest with simple care: seal cracks as they appear, sealcoat once the asphalt has cured, and restripe on schedule. Local Appell owners can take over that maintenance after the project, so the new lot stays looking new.

How we work

  • Site assessment. Measure the lot from current aerial imagery, then walk it to scope milling depth and base repairs.
  • One proposal. Clear, itemized pricing submitted through your facilities portal if you use one.
  • Phasing plan. A plan that keeps entrances, drive-thrus and customers moving.
  • Mill, pave & roll. Our vetted paving partners do the work; your Appell manager runs the job.
  • Stripe & document. Fresh layout, before and after photos and closeout in your portal.
Milling & paving is an Appell National service. It's managed centrally for multi-site customers. For a single location, your local Appell owner can help with repairs, sealcoating and striping.

Milling & Paving FAQs

Do you mill and pave for single locations?

Milling and paving is managed by Appell National for multi-site and national customers. Local Appell owners can help with repairs, crack filling, sealcoating and striping.

Can the site stay open?

In most cases, yes. We phase the work and schedule nights or weekends so entrances and drive-thrus stay usable.

How do I submit a project?

Through your facilities portal (ServiceChannel, Fexa, OpenWrench, fmPilot2, CorrigoPro, FM Dashboard, Ecotrak, ServiceNow) or directly to Appell National Accounts.

Is striping included?

Yes. Every resurfacing ends with a fresh layout so the site reopens ready.

How deep is parking lot milling?

Usually an inch and a half to a few inches, depending on the condition of the surface and the new asphalt thickness. Failed base areas are dug out deeper and rebuilt.

How long does a new asphalt lot last?

With regular crack sealing, sealcoating and restriping, a well-built asphalt lot can last 15 to 20 years or more.

How soon can cars drive on new asphalt?

Usually within a day or two, depending on temperature. We plan the phasing so parts of the lot stay open.

When is paving season?

Asphalt plants run in warm months. In northern markets, paving is typically done from spring through fall; in the South the season is longer.

One partner for every lot you manage.

Local Appell owners in 24 markets, a vetted network in all 50 states, and one team accountable for the work.

//Find your local Appell →Talk to National Accounts